How to install an accumulator in a boiler?

An accumulator is a gadget that exploits the heat emitted by the boiler to produce sanitary hot water. That’s right, this set makes it easier for you to save energy, improve the efficiency of the heating system and warm you throughout the season, giving you the possibility to enjoy a bath with the interesting hot water obtained, we are sure that your family will be very happy with this novelty. If you want to exploit the synergy between these two devices, you need to know how to arrange a joint to a boiler and now we will explain the development point by point.

What is and how does an accumulator work?

An accumulator can be defined as a water tank that can be connected to a boilerHowever, they quite call a tank with resistance in this same way that is with the ability to heat water without dependence. For this reason, we will determine the two devices so that you can understand the procedure precisely.

one thermoaccumulator it does not need a boiler to work, since it has a resistance inside that heats the water up to the temperature that the user selects. Thanks to your exercise system this electronic makes a substantial energy expenditure which is equivalent to money.

On the other hand, a hot water accumulator it is a tank that is installed in the boiler, it stores water and the success using the energy of the heating system, then the savings that are related to its functionality are quite greater.

If you want to have the positive results of an accumulator and want to save a few euros by installing it yourself, follow the steps that we indicate now and transform your boiler into a set that the family will love.

How to connect an accumulator to a boiler point by point

The development of installation of a hot water storage tank it’s not simple, you have to protect a lot of data to avoid problems and get the result you want. It is suggested that the work is carried out by trained personnel who have the essential utilities, in this way any kind of dangers will be prevented.

If you feel ready to do this work, here we show you a succession of steps that have the possibility of advising you throughout the development. The procedure taught here is general, it can be used on different types of boilers, but remember to have the manual provided by the developer of the set you purchased handy.

Step 1: Select the location

Your new accumulator must be installed in a clean and cool space, do not leave it in the open choose a correct space according to its distance in relation to the boiler and subjectively close to the place where the hot water, that way you won’t lose temperature during the walk through the pipes. The accumulator can be positioned on the floor on a particular base or on the wall, this will depend on your elements and the type of tank.

Step 2: Run the health connection

In this step you need to find out the developer’s manual of the accumulator, as it is necessary to detail the procedures that need to be carried out in order to carry out these connections. It is advisable to insulate the water pipes in order to avoid the lack of heat and to wash before installation, to avoid that metal particles affect the correct exercise of the set. It is essential to isolate the piping circuits using isolation valves, and it is also suggested to have a non-return valve for the cold water.

Step 3: Arm the electrical connection

This type of connections depends on the model and brand of your set and in the same way as the previous situation the manual can offer you the essential information. You have to figure out the schematics and electrical diagrams shown. It is necessary to take into account the corrosion of the accumulator, then it is necessary to connect it to the ground. Remember to cut off the power supply before starting work.

Step 4: Check the temperature

To avoid accidents such as hot water, what is really suggested is to have a thermostatic mixing valve, whose locality is in the drain of the installation. For safety reasons remember to never carry out the installation over the accumulator and not to use automotive antifreeze as it can be toxic.

Step 5: Check the security of the installation

Before carrying out the final exercise test you must check that the set goes safely. Look at the electrical connections, confirm that the installation is full of water and purge it, check the connections back and forth, that the thermostat is set correctly and that there are no leaks of any kind.

Step 6: Try the hot water tank exercise

When you have done the safety check, confirm that the gasket is always full and at the correct pressure, then adjust the pressure in the primary circuit of the accumulator. To remove air from the accumulator and fill it, simply open the hot water valve. Open the fill valve and the shut-off valves, close the hot water valve as soon as you see that the flow has stabilized and then there is no air for the time being. At this time you must monitor the tightness of the connections of the installation. Finish by filling the primary circuit of the accumulator, verify that the drain valve is closed, open the cut-off valves of the heating circuit connected to the boiler and clean the air.